Home >> Products >> Press Machine

APC Series Double-Crank Precision Steel Frame Press Machine

APC Series precision metal stamping press adopts a multi-direction motion system, in which connecting rods are installed between double cranks and these rods are used to bear the load from two wide operation centers-ram and bolster. These designs help to prevent forward tilt- the direct cause to produce deviation. in this way, stamping's high-precision and small vibration could be well guaranteed, Therefore, the stamping press is quite suitable for multi-station precision pressing.

Description

Features:

1. With High rigidity rack design, they are welded with the use of high-quality steel plates, through relieving stresses,so that stability and reliability and of the whole machine in precision are enhanced.

2. Machine adopts high-alloy-steel, two-bent-axle, and two-wide work center, to optimize design.

3. In order to guarantee relative stationarity of machine operation, it is necessary to balancers.

4. Moulding-adjustment precision is as high as 0.1mm, safe,speedy ,and reliable .

5. Through hard oxidation and grinding ,such parts as bent axles,gear sets,and connecting rods possess higher combination property and tolerance.

6. Adopt highly sensitive and reliable clutch/brake and internationally top duplex,to guarantee precision an operation and stop of press

7. Machine's structural design shall be reasonable,for the convenience of realizing automatic production,red and improving

8. Possess advanced design concepts, low noise, low consumption, and energy


Standard configuration:                                                                   

>Dry clutch brake                                                                                    

>Strandard operating ststem                                                                          

>Choice/cutting/inch/safe journey/continuation of operating mode                                     

>Oil pressure overload protection device                                                             

>Over-run safety device                                                                              

>Misfeed detection consent                                                                           

>Electric slider adjusting device                                                                   

>Diagital moulding-height indicator (unit:0.1mm)                                                     

>Auto grease pump device                                                                             

>Accumulative counter(6 digits)                                                                      

>Pre-determined counter(6 digits)                                                                    

>Maintenance counter (6 digits)                                                                      

>Life counter(6 digits)                                                                              

>Electronic rotatry cam switch (6 connections)                                                      

>Air-blast device 1/2" secondary ciruit                                                              

>Error inspection socket                                                                             

>Power socket (only apply to single-phase 110V power)                                             


Optional configuration:

>Wet clutch brake

>Die cushion device

>Vs variable-speed motor

>Touch-screen device

>Photo-electic safety device

>Upper slider feeding device

>Main motor inversion device

>Foot switch

>Safety dog and safety latch

>T-type two-hand button perating floor

>Inspection variable-connection magnetic value

>Anti-vibration mechanical foot

>Rapid tooling exchange

>Upper die clamper

>Lower die clamper

>Die lifter

>Mould-shift arm


Technical parameters

Name
APC-110APC-160APC-200APC-250
Model
V typeH typeV typeH typeV typeH typeV typeH type
CapacityTon110160200250
Rated tonnage pointmm53636373.5
Strokemm180110200130250150280170
Stable speeds.p.m35-6550-10030-5540-8525-4535-7020-3530-60
Die heightmm400435450455500550550605
Slide adjustmentmm100100120120
Bolster areamm1800x650x1302000x760x1502400x840x1702700x900x170
Slide areamm1400x500x701600x550x701850x650x952100x700x95
Main motorkw.p11x415x418.5x422x4
Presses weightTon14.22027.545.5
Air pressurekg/cm25555
Presses precision
GB(JIS)1class
Die cushion capacity
Two plate & two cylinders
CapacityTon3.6 x 26.3 x 210 x 214 x 2
Air pressurekg/cm26666
Strokemm707080100
Die cusion work part dimensionmm2350 x 235 x 2 组410 x 260 x 2组540 x 350 x 2组640 x 470 x 2组


APC Technical Parameter.PDF